Digital Monitoring Products Canadian XR100 Bedienerhandbuch PDF herunterladen (Seite 31)

XR100 Series Programming Guide Digital Monitoring Products

Remote options

7.6

PC MODEM NO YES

PC Modem

YESallowsthepaneltoanswerthetelcolinkandconnectwithRemoteLink

throughthePCModemat2400baud.NOdisablesPCModemcommunication.

7.7

ALR RCVR NO YES

Alarm Receiver Authorization

SelectYEStoenableremotecommandsandprogrammingtobeacceptedfromthe

alarmSCS-1RReceiver.TheRemoteKeyoptioncanalsoberequired.

WithYESselected,thepanelrequeststhereceiverkeyduringitsrstcommunication

withtherstSCS-1RReceiver.Thepanelretainsthisalarmreceiverkeyinmemoryand

allows remote commands to be accepted from the alarm receiver. If an alarm occurs

during a remote connect, the alarm report is immediately sent to this receiver only.

When NO is selected, remote commands and programming are not accepted from the

alarmSCS-1RReceiver.

7.8

SVC RCVR NO YES

Service Receiver Authorization

YESenablesremotecommandsandprogrammingtobeacceptedfromasecondary

servicereceiverotherthanthealarmSCS-1RReceiver.TheRemoteKeyoptioncanalso

be required.

WithYESselected,thepanelrequeststheservicereceiverkeythersttimeitis

contacted by the service receiver. The panel retains this service receiver key in memory

and accepts remote commands from the service receiver.

If an alarm occurs during a remote connect, the panel disconnects from the service

receiver and calls the alarm receiver. Alarm reports are only sent to the alarm receiver.

It is important that the alarm receiver key and the service receiver key programmed

at the central station are NOT the same so the panel can determine the difference

between receivers.

When NO is selected remote commands and programming are not accepted from a

secondary service receiver.

ThisoptionmustbeYEStoallowprogrammingfromadirectlyconnectedcomputeror

aniCOM/iCOM-E.

7.9 Manufacturer Authorization

SelectYEStoallowDMPTechnicalSupporttechnicianstoaccessthepanelduring

system service or troubleshooting. This authorization automatically expires within

one hour.

DMP remote service is provided on a read only basis: DMP technicians can look

at the system programming and make suggestions only. Alterations can only be

accomplished by installing company service personnel.

7.10 Allow Network Remote

Thisoptiondisplaysonlyifthepanelhasnetworkcapability.YESallowsremote

programming over the network. Changing this option does not change any other

networkprogrammingoptions.DefaultisYES.

7.10.1

NETWORK PROG

Network Programming Port

PORT: 2001

Entertheprogrammingportnumber.Theprogrammingportidentiestheportused

to communicate messages from the panel. The default Programming Port setting is

2001.

7.10.2 Encrypt Network Remote

YESencryptsdatasentovernetwork.DefaultisNO.

7.11 Allow Cellular Remote

YESallowsremoteprogrammingusingcellularconnection.DefaultisYES.

7.11.1 First GPRS APN

EntertherstAPN(AccessPointName).Thisallowsanaccesspointforcellular

communication and is used to connect to a DNS network. The APN may contain two

linesof16characterstoequal32characters.DefaultissettoSECURECOM400.

Second GPRS APN

EnterthesecondAPN(AccessPointName).Thisworksasabackupincasetherst

APNfails.TheAPNmaycontaintwolinesof16characterstoequal32characters.

DefaultissettoSECURECOM400.

SECURECOM400

FIRST GPRS APN

AUTH? NO YES

ALLOW NETWORK

REMOTE? NO YES

MANUFACTURER

ENCRYPT NETWORK

REMOTE? NO YES

ALLOW CELL

REMOTE? NO YES

SECURECOM400

SECOND GPRS APN

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 77 78

Kommentare zu diesen Handbüchern

Keine Kommentare

Digital Monitoring Products Canadian XR100 Bedienerhandbuch Seite 31

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Digital Monitoring Products Canadian XR100