Digital Monitoring Products Canadian XR100 Bedienerhandbuch PDF herunterladen (Seite 19)

XR100 Series Programming Guide Digital Monitoring Products

CommuniCation

3.20

PROTOCOL: TCP

Protocol

ThisoptiondisplaysonlywhenCommunicationTypeisNET.

SelectTCPtocommunicateoverthenetworkusingTCPprotocol.SelectUDPto

communicateusingUDPprotocol.DefaultisTCP.

3.21

RETRY SECONDS: 6

Retry Seconds

ThisoptiondisplaysforNETCommunicationTypes.

Enterthenumberofseconds(between6and15)thepanelshouldwaitbefore

retrying to send a message to the receiver if an acknowledgment was not received.

The panel retries as many times as possible for a period of one minute before

sending a network trouble message. For example, if retry time is set to 15, the

panelretriesfourtimes.ThedefaultRetryTimeis6seconds.

Note:IfTCPisenabled,theminimumRetryTimeprogrammedis6seconds.

3.22

SUB CODE NO

Substitution Code

ThisoptiondisplayswhentheCommunicationTypeisNET,orCELL.ThePanel

Substitution Code increases the level of security by helping to ensure that the

panel sending the message to the receiver has not been substituted by another

panel. The default is NO.

SelectYEStosendasubstitutioncodewitheverymessage.

SelectSHARED(SHR)tousethesamesubstitutioncodeasoperatingintheprevious

path.

3.23

893A: NO YES

893A

This option displays when the Communication Type is DD or CID.

The893AoptionallowsreportstobesenttothereceiveronasecondDDlineusing

the893Amodule.DefaultisNo.

Whenusingthisoption,TestReportmessages(S07AutomaticRecallTestorS88

UnrestoredSystemRecallTest)willbesenttothereceiveratthefrequency

programmedinTestFrequency,alternatingbetweentherstandsecondphone

line.

Forexample,aDDpathwithan893Amodulesetfordailytestreportfrequency

willsendatestreportthroughphoneline1onedayandphoneline2thenextday.

If893AoptionissettoYES,enteruptoa3digitprextobedialedbeforethe

secondphonenumber.Ifnoprexisentered,thesecondphonenumberisdialedas

originally entered.

3.24

ALARM SWITCH: 1

Alarm Switch

This option displays for DD or CID Communication Types.

Enterthenumberofattemptstosendanalarmmessagebeforeswitchingto

thenextpath.Rangeisfrom1to10.Allnon-alarmmessageswillbesentfor

10 attempts on the dialer before a switch is initiated. If the path immediately

following this channel is not a backup path, this option has no effect. Default is 1.

3.25

DUPLICATE ALARMS

Duplicate Alarms

ThisoptiondisplaysforBACKUPpaths.IfYesisselected,thecurrentbackuppath

duplicates all alarms occurring on its group primary path. Default is No.

3.26

ALARM YES

Alarm Reports

This option displays when the Path Type is Primary. All backup paths within the

group follow the same programming for Alarm Reports. Default is Yes.

NO YES FIRE

WhenYESisselected,thefollowingreportsaresenttothereceiverforallzone

types:

    •Alarm •Bypass •Reset •Restore

WhenFIREisselected,thefollowingreportsaresentforFire,FireVerifyand

SupervisoryZones:

    •Alarm •Bypass •Reset •Restore

NO YES SHARED

2ND LINE PREFIX:

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 77 78

Kommentare zu diesen Handbüchern

Keine Kommentare

Digital Monitoring Products Canadian XR100 Bedienerhandbuch Seite 19

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Digital Monitoring Products Canadian XR100