Digital Monitoring Products XR550 Bedienerhandbuch PDF herunterladen (Seite 56)

Digital Monitoring Products XR150/XR350/XR550 Series Programming Guide

ZONE INFORMATION

DMP Wireless

For a DMP 1100X Wireless Receiver set the House Code from 1 to 50. See House Code programming in System

Options. Zones 500 through 999 can be programmed as Wireless zones. Briey reset the panel using the J16 jumper

to activate Wireless operation. Refer to the XR150/XR350/XR550 Series Installation Guide (LT-1233).

For an 1100 Series Key Fob see section 18.11.

NOTE: All wireless programming is stored in the panel. The 1100X Wireless Receiver obtains the necessary

programming information from the panel each time the receiver powers up, when the programmer STOP routine is

selected or the panel is reset. The receiver memory refresh takes up to 10 seconds to complete depending on the

number of wireless zones programmed and the Red LED remains on during this time. Normal receiver operation is

inhibited during the memory refresh period.

18.10 Wireless

Select YES to program this zone as a DMP wireless zone. You must program the wireless

House Code prior to adding DMP wireless zones to the system.

See House Code programming in System Options. Default is NO.

18.10.1 Serial Number Entry

Enter the eight-digit serial number found on the wireless device.

This message displays when the serial number is already programmed for another zone.

The programmed zone number displays.

18.10.2 Contact

This option displays if the serial number entered is for an 1101, 1103, or 1106 Universal

Transmitter or 1114 Wireless Four-Zone Expander. Press any top row key to select the

contact.

This option displays when programming an 1101, 1103, or 1106 Transmitter. Select INT to

use the internal reed switch contacts. Select EXT to connect an external device to the

1101, 1103, or 1106 terminal block. Default is INTERNAL.

By allowing both of the transmitter contacts (INT and EXT) to be used at the same

time, two zones may be programmed from one transmitter. When using both contacts,

you must use consecutive zone numbers. Zones 531 and 532 or zones 890 and 891 are

acceptable zone assignments.

For example, program transmitter serial number 01345678 as Zone 521 with an INT

contact type and Zone 522 with an EXT contact type. The same serial number is used for

both zones.

This option displays when programming the 1114 Wireless Four-Zone Expander with four

input contacts. The same serial number is used for all four contacts. Select the contact

number to program. When using the contacts, you must use consecutive zone numbers.

Default is Contact 1.

For example, use serial number 08345678 to program Contact 1 for Zone 561, Contact 2

for Zone 562, Contact 3 for zone 563, and Contact 4 for zone 564.

A tamper on the 1114 is transmitted as the zone number assigned to Contact 1.

This message displays when the Contact is already programmed for another zone. The

programmed zone number displays.

This option only displays when EXT is selected as the Contact type. For external devices

connected to the 1101, 1103 or 1106 terminal block, select NO to use normally closed

(N/C) contacts. Select YES to use normally open (N/O) contacts.

Default is NO.

18.10.3 Supervision Time

Press any top row key to select the supervision time required for the wireless zone. Press

COMMAND to accept the default time. Default is 240 minutes.

Note: Refer to the Wireless Check-in and Supervision Time Denitions section of the

Appendix for supervision information.

Press the Select key under the required number of minutes. The transmitter must check

in at least once during this time or a missing condition is indicated for that zone. 1100

Series transmitters automatically checkin based on the supervision time selected for

the wireless zone, no additional programming is needed. If two zones share the same

transmitter, the last programmed supervision time is stored as the supervision time for

both zones. Zero (0) indicates an unsupervised transmitter.

ZONE INFORMATION

WIRELESS? NO YES

TRANSMITTER

SERIAL#: XXXXXXXX

ALREADY IN USE

ZONE NUMBER: XXX

TRANSMITTER

CONTACT:XXXXXXXX

TRANSMTR CONTACT

INT EXT

TRANSMTR CONTACT

1 2 3 4

ALREADY IN USE

ZONE NUMBER: XXX

ZONE INFORMATION

NORM OPN NO YES

TRANSMITTER

SUPRVSN TIME: 240

SELECT MINUTES:

0 3 60 240

1 2 ... 51 52 53 54 55 56 57 58 59 60 61 ... 77 78

Kommentare zu diesen Handbüchern

Keine Kommentare

Digital Monitoring Products XR550 Bedienerhandbuch Seite 56

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Digital Monitoring Products XR550