Digital Monitoring Products XR550 Bedienerhandbuch PDF herunterladen (Seite 34)

Digital Monitoring Products XR150/XR350/XR550 Series Programming Guide

SYSTEM OPTIONS

System Options

9.1 System Options

This section allows you to select system-wide parameters.

9.2 System

This option allows you to program how the areas operate for arming and disarming. The

options you can choose are listed below:

AREA - All 32 areas can be programmed and operated independently.

ALL/PERIMETER - Area 1 is the Perimeter and Area 2 is the Interior.

HOME/SLEEP/AWAY - Area 1 is the Perimeter, Area 2 is the Interior, and Area 3 is the

Bedrooms. With the HOME/SLEEP/AWAY option, the user can:

• 1. Select HOME to arm just the perimeter.

• 2. Select SLEEP to arm the perimeter and interior (non bedroom areas).

• 3. Select AWAY to arm all three areas.

Note: A Home/Sleep/Away system can be congured to use all three areas or only use the

Home and Away areas.

HOME/SLEEP/AWAY WITH GUEST- This allows the alarm system to be divided into a main

house HOME/SLEEP/AWAY system and two other guest houses that also are set up as HOME/

SLEEP/AWAY systems.

Areas 1, 2, and 3 are the Perimeter, Interior, and Bedrooms for the Main house system.

Areas 4, 5, and 6 are the Perimeter, Interior, and Bedrooms for the Guest 1 house system.

Areas 7, 8, and 9 are the Perimeter, Interior, and Bedrooms for the Guest 2 house system.

These areas are automatically assigned per system and cannot be changed. See Display

Areas in Device Setup to assign keypads to a system. Zones are assigned to a system by

assigning the system’s area numbers to the zone in Zone Information programming.

When either All/Perimeter or Home/Sleep/Away is selected, the area names are

automatically assigned and cannot be modied.

Note: Areas 3-32 in an All/Perimeter system, areas 4-32 in a Home/Sleep/Away system,

and areas 9-32 in a Home/Sleep/Away with Guest system are not available for use and are

initialized.

9.3 Instant Arming

When YES is selected, the arming keypad displays INSTANT for selection during the exit

countdown delay when arming fewer than all areas of the system. At the time instant

arming is selected, any entry and exit delays programmed for the areas being armed are

ignored. The entry delay for previously armed areas is not affected by instant arming.

When NO is selected, INSTANT does not display during arming. Default is NO for an Area

System, and YES for an All/Perimeter or Home/Sleep/Away system.

9.4 Closing Wait

When YES is selected, the keypad displays ONE MOMENT... while waiting for an

acknowledgement from the receiver before arming the selected area(s) and performing a

Bell Test (if selected). Exit delays begin after the Closing Wait. Opening/Closing reports

must be YES to enable Closing Wait.

9.5 Entry Delay 1

Enter the Entry Delay time for all Exit type zones programmed to use Entry Delay 1. When

an armed Exit type zone is faulted, the keypad prewarn tone begins sounding. All keypads

programmed to prewarn for that zone display ENTER CODE:- and the name of the zone

causing the entry delay. When the rst digit of a code is entered, the prewarn tone stops

at that keypad. If an invalid code is entered, the prewarn tone begins sounding again. The

area must be disarmed before the delay expires or an alarm report is sent to the receiver

and an alarm sounds. All zones in that area are delayed along with the Exit zone. Entry

Delay times can be from 30 to 250 seconds. Repeat the above for each entry delay being

used in the system.

Note: Specic Exit Error operation is based on the Entry Delay used (1-4) with an EX type

zone. See Exit Delay.

Note: For UL Installations, the combined Transmit Delay (Abort Window) and Entry Delay

must not exceed one (1) minute.

9.6 Cross Zone Time

Enter the time allowed between zone faults. When zones are cross zoned, the same zone

or a second cross zoned zone must fault within this time in order for an alarm report for

both zones to be sent to the receiver. If the cross zone time expires without the second

zone faulting, only a zone fault from the rst zone is reported. Cross-zone time can be

from 4 to 250 seconds. Entering 0 (zero) disables this function. Default is 4.

See the Appendix.

SYSTEM OPTIONS

SYSTEM: AREA

AREA A/P H/A GST

INST ARM NO YES

CLS WAIT NO YES

ENTRY DLY 2: 60

ENTRY DLY 3: 90

ENTRY DLY 1: 30

ENTRY DLY 4: 120

CRS ZONE TM: 4

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 77 78

Kommentare zu diesen Handbüchern

Keine Kommentare

Digital Monitoring Products XR550 Bedienerhandbuch Seite 34

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Digital Monitoring Products XR550