Digital Monitoring Products XR550 Bedienerhandbuch PDF herunterladen (Seite 11)

XR150/XR350/XR550 Series Programming Guide Digital Monitoring Products

INTRODUCTION

Introduction

1.1 Before you Begin

This guide provides programming information for the DMP XR150/XR350/XR550 panel. After this Introduction, the

remaining sections describe the functions of each programming menu item along with the available options. Before

starting to program, we recommend that you read through the contents of this guide. The information contained

here allows you to quickly learn the programming options and operational capabilities of the panel.

In addition to this guide, you should also read and be familiar with the following documents:

• XR150/XR350/XR550 Series Installation Guide (LT-1233)

• XR150/XR350/XR550 Series Programming Sheet (LT-1234)

• XR150/XR350/XR550 User’s Guide (LT-1278)

• XR150/XR350/XR550 Compliance Listing Guide (LT-1330)

Internal Programmer

The panel contains all of its programming information in an on-board processor and does not require an external

programmer. You can perform all programming tasks through a 32-character DMP alphanumeric keypad set to

address one.

Programming Information Sheet

Included with each panel are the Programming Information Sheets. These list the various programming

prompts and available options for programming the panel. Before starting to program, we recommend you

completely ll out each sheet with the programming options you intend to enter into the panel.

Having completed programming sheets available before entering data helps prevent errors and can shorten

the time you spend programming. Completed sheets also provide you with an accurate panel program record

you can keep on le for future system service or expansion. The remainder of this Introduction provides

instructions for starting and ending a programming session using the alphanumeric keypad.

1.2 Getting Started

Ground Yourself Before Handling the Panel! Touch any grounded metal, such as the enclosure, before touching the

panel to discharge static.

Remove All Power From the Panel! Remove all AC and battery power from the panel before installing or

connecting any modules, cards, or wires to the panel.

Before starting to program the panel, make sure the panel is properly grounded and AC and battery power is

applied to the appropriate panel terminals. All wiring connections and grounding instructions are detailed in the

XR150/XR350/XR550 Series Installation Guide (LT-1233).

Program from any Keypad Address or Wireless Keypad

You can program the panel from any 32-character wireless keypad or hardwired keypad connected to the panel’s

keypad data bus. See the XR150/XR350/XR550 Installation Guide (LT-1233) for keypad addressing and installation

information for hardwired keypads.

Wireless Keypads can be used for panel programming after being programmed in the panel manually or by using the

Wireless Keypad Association operation.

• To enable association operation in the keypad, access the Installer Options Menu (3577 (INST)) and select

RF Survey. The keypad logo LEDs turn on Red until association is successful.

• To enable association operation in the panel, reset the panel 3 times within 12 seconds. Allow the panel’s

keypad bus Transmit/Receive LEDs to turn back on between each reset.

• For 60 seconds the panel listens for wireless keypads that are in the Installer Options Menu and have not

been programmed, or associated into another panel. Those keypads are assigned to the rst open device

position automatically based upon the order in

which they are detected. The keypad logo turns

Green to indicate it has been associated with

the panel. See the 9000 Series Wireless Keypad

Installation Guide

(LT-1107) for additional information.

Accessing the Programmer

1. Momentarily place the Reset jumper over both of

the J16 pins to reset the panel.

2. Enter the code 6653 (PROG) and press COMMAND.

3. The keypad displays: PROGRAMMER.

To enable Wireless Keypad

Association operation:

Reset panel 3 times within

12 seconds.

To access the programmer:

Momentarily place the

Reset jumper over both of

the J16 pins to reset the

panel.

Figure 1: XR550 Series Panel Showing Reset

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 77 78

Kommentare zu diesen Handbüchern

Keine Kommentare

Digital Monitoring Products XR550 Bedienerhandbuch Seite 11

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Digital Monitoring Products XR550