Digital Monitoring Products XR550 Betriebsanweisung PDF herunterladen (Seite 19)

XR150/XR350/XR550 User Guide 15Arming and Disarming

Insome cases,you mightseethe keypaddisplay FRONTDOOR—

FAULT.Thekeypadthendisplayspriorityzonewhichisazonethat

cannotbebypassed.Theproblemonthezonemustbecorrected

before the system can be armed.

Whenchoosingtobypassa protectiondevice orzone, theremay

be a pre-programmed maximum number of zones (up to 8) that

can be bypassed in an area when that area is being armed. This

limit is programmed at installation.

Arming Messages:

For Area systems the keypad briey displays SYSTEM ON if only

selectedareasarearmed.ThekeypadbrieydisplaysALLSYSTEM

ONwhenallareasinthesystemarearmed.

For All/Perimeter systemsthekeypad brieydisplays PERIMETER

ONifonlyselectedareasarearming.Thekeypadbrieydisplays

ALLSYSTEMONwhenallareasinthesystemarearmed.

For Home/Sleep/AwaysystemsthekeypaddisplaysHOMESYSTEMON

or SLEEP SYSTEM ON if only selected areas are arming. The keypad

brieydisplaysALLSYSTEMONwhenallareasinthesystemarearmed.

For Home/Sleep/Away with Guest systems the main system arms

the same as a Home/Sleep/Away system. A keypad assigned to the

rstguesthousesystemdisplaysHOMEGUEST1ONorSLEEPGUEST1

ONifonlyselectedareasarearming.ThekeypaddisplaysALLGUEST

1ONwhenallareasintheguesthousesystemarearmed.

Exit Delay: The keypad then displays the exit delay time as it counts

down. Your system may be pre-programmed at installation to beep

the exit delay tone at eight-second intervals until the last 10 seconds

when the keypad beeps at three-second intervals. After exiting the

building, if you re-enter during the countdown the exit countdown

restarts, allowing additional time to then disarm or again exit the

building during the countdown. This restart can occur only one time.

Whentheexitdelaytimeexpires,alldisarmedzonesarearmed.

Note: If your system uses a keyswitch to arm an area, the exit

delaytimedoesNOTshowonthekeypaddisplay.

When you arm both the Perimeter and Interior to leave the

building but then you do not exit by the time the exit delay ends,

thesystemautomaticallyarmsbuttheinteriorarea(s)willremain

disarmed because you have not exited.

Should you exit the building and the door does not close properly,

your system may be programmed so that when the exit delay

countdown ends, then the entry delay starts and the bell will sound

to alert you to the situation. Enter your user code to stop the bell

and disarm the system. Rearm the system, exit the building, and

make sure the door is securely closed.

ONE MOMENT . . . Message: If your system is monitored, it

may be programmed to wait for the arming report transmission

to the central station before displaying the armed mes sage. This

veriesyourphonelinesareworkingproperly.Whilethesystemis

waitingforthetransmission,thedisplayreadsONEMOMENT...If

the report is received, the keypad displays the armed message. If

thereportisnotreceived,thekeypaddisplaysLOCALALARMONLY

before displaying the armed message.

Note: Your system may be pre-programmed at installation to:

—sendarmingorzonebypassingreportstoacentralstation

—armand/ordisarmspecicareasatspecickeypads.

Key Fob Arming

Press and hold the key fob button programmed for Arming or the Toggle

arm/disarm button. The Red LED two-second acknowledgement light

indicatesAllSystemOn.TheGreen/Redtwo-secondacknowledgement

lightindicatesSystemOnwithsomeareasarmed.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 87 88

Kommentare zu diesen Handbüchern

Keine Kommentare

Digital Monitoring Products XR550 Betriebsanweisung Seite 19

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Digital Monitoring Products XR550