Digital Monitoring Products XR20 Installationsanleitung Seite 38
- Seite / 52
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Digital Monitoring Products XRSuper6/XR20/XR40 Programming Guide
30
zone informaTion
11.10.3
SUPRVSN TIME: 0
Key Fob Supervision Time
Press any top row key to select the supervision time required for the key fob zone.
Press COMMAND to accept the default time. Default is 0.
0 3 60 240
Press the Select key under the required number of minutes. The key fob must check
in at least once during this time or a missing condition is indicated for that zone.
1100 Series key fobs automatically checkin based on the supervision time selected
for the wireless zone, no additional programming is needed. Zero (0) indicates an
unsupervised transmitter.
Note: When the panel is reset or a receiver is installed or powered down and
powered up, the supervision timer restarts for all wireless zones.
11.10.4
BUTTONS: 4
Number of Key Fob Buttons
Enter the number of buttons (1, 2, or 4) on the key fob being programmed. Default
is four buttons.
Note: If the key fob is a one-button model, programming continues at the Button
Action section. Default button assignment for one-button key fobs is a Panic Alarm
(PN) with no output assigned.
11.10.5
TOP BTM LFT RGT
Key Fob Button Selection (Four Buttons)
This prompt only displays if the key fob being programmed is a four-button model.
Press the Select key under the key fob button to program. The following list
identies the default button assignments:
TOP Arming with areas 1, 2, and 3 assigned
BTM Disarming with areas 1, 2, and 3 assigned
LFT Panic Alarm (PN) with no output assigned
RGT Arming with Area 1 assigned
11.10.6
TOP BTM
Key Fob Button Selection (Two Buttons)
This prompt only displays if the key fob being programmed is a two-button model.
Press the Select key under the key fob button to program. The following list
identies the default button assignments:
TOP Arming with areas 1, 2, and 3 assigned
BTM Disarming with areas 1, 2, and 3 assigned
11.10.7
ACTION: XXXXXXX
Button Action
This option species the Button Action for an individual key fob button. The default
action for the button selected is displayed. Press any Select key to display the
Button Action options. To view more options press the COMMAND key.
ARM DIS TGL STA
ARM (Arm) - Arms selected areas and force arms bad zones.
DIS (Disarm) - Disarms selected areas.
TGL (Toggle Arm) - Toggles arm/disarm for selected areas and force arms bad zones
when arming.
STA (Status) - Causes the key fob LED to indicate the arm/disarm status of the
system.
PN PN2 EM EM2
PN (Panic) - Triggers a Panic zone type alarm with no restoral.
PN2 (Panic 2) - Triggers a Panic zone type alarm with no restoral when pressed
simultaneously with any other Panic 2 button. No action occurs when pressed
alone.
EM (Emerg) - Triggers an Emergency zone type alarm with no restoral.
EM2 (Emerg 2) - Triggers an Emergency zone type alarm with no restoral when
pressed simultaneously with any other Emergency 2 button. No action occurs when
pressed alone.
OUT RST UN
OUT (Output) - Causes an output to turn on steady, pulse, momentary, toggle or off.
RST (Sensor Reset) - Causes the panel to perform a standard Sensor Reset.
UN (Unused) - The button is not used and performs no action.
- Programming guide 1
- MODEL XRSuper6/XR20/XR40 2
- COMMAND PROCESSOR 2
- PROGRAMMING GUIDE 2
- Table of ConTenTS 3
- Stop 35 6
- Appendix 36 6
- Revisions to this Document 8
- Introduction 9
- 1.3 Programming Menu 10
- 1.4 Programmer Lockout Codes 10
- 1.5 Reset Timeout 10
- 1.6 Power Up 10
- JONES RESIDENCE 11
- FRI 12:51 PM 11
- 5 6 7 8 12
- 1 2 3 4 12
- 9 0 CMD 12
- Initialization 14
- Communication 15
- Remote Options 20
- Remote Disarm 21
- System Reports 22
- System Options 23
- Bell Options 27
- Output Options 28
- Arm-Alarm Output 30
- Output Information 31
- Area Information 32
- Zone Information 33
- Serial Number Entry 36
- Output Number 39
- Set Lockout Code 43
- Appendix 44
- 14.7 Cross Zoning 47
- 14.10 Zone Type Descriptions 50
- 14.11 Zone Type Defaults 51
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Digital Monitoring Products XR20
Sicherheitszugriffskontrollsysteme Digital Monitoring Products XTL Series Bedienungsanleitung
(18 Seiten)
(18 Seiten)
Sicherheitszugriffskontrollsysteme Digital Monitoring Products XTL Series Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Sicherheitszugriffskontrollsysteme Digital Monitoring Products Canadian XR100 Installationsanleitung
(36 Seiten)
(36 Seiten)
Sicherheitszugriffskontrollsysteme Digital Monitoring Products XR20 Installationsanleitung
(31 Seiten)
(31 Seiten)
Panasonic TXL32C2EA Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Audio Panasonic TXL32C2EA.
Wir stellen 3 PDF-Handbücher Panasonic TXL32C2EA zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Kommentare zu diesen Handbüchern