Digital Monitoring Products Canadain XR500 Bedienerhandbuch PDF herunterladen (Seite 17)

XR500 Series Programming Guide Digital Monitoring Products

CommuniCation

Communication

3.1

COMMUNICATION

Communication

Congure the communication options for the panel. The information you program varies

with the Communication Type you select.

3.2

ACCOUNT NO: 12345

Account Number

The Account Number is a 1 to 5 digit number used to identify which panel is sending a

message. Enter the account number sent to the SCS-1R Receiver. Messages may be sent

to a central station or via PC Log Reports to a PC. The default is 12345.

NET, CELL, 232 and DD - The range of valid account numbers for a panel is 1 to 65535.

For accounts of four digits or less, do not enter leading zeros.

CID - Choose an account number between 1 and 9999.

3.3

XMIT DELAY: 30

Transmit Delay

Enter the number of seconds (15 to 45) the panel waits before sending burglary

zones (Night, Day, or Exit) reports to the receiver. Other zone type reports are sent

immediately. Alarm bells and relay outputs are not delayed during this period. Program

Burglary Outputs for pulsed or steady, and set Abort Reports to YES if Opening and Closing

reports are not being sent. Enter 0 (zero) to disable this function. The default is 30.

If the area where the alarm occurred is disarmed during the Transmit Delay time, only an

Abort Report (S45) message is sent to the receiver. If the area where the alarm occurred

is disarmed after the alarm message is sent to the receiver but before the Bell Cutoff

time expires even if the alarm was silenced, an Alarm Cancelled (S49) message is sent.

Otherwise the alarm is sent at the end of the delay. The Alarm Cancelled report cannot

be disabled.

Note: For Commercial Burglary Installations, the combined Transmit Delay

(Abort Window) and Entry Delay must not exceed one (1) minute.

3.4 Communication Path

Up to eight communication paths may be programmed. Each path is designated as a

primary or backup communication route. Path 1 is always Primary but other paths may be

programmed as additional primary or backup.

Each primary path establishes a new path group. A path group is made up of the primary

path and its subsequent backup paths. Typical communication takes place on the primary

path with backup paths being used only when the primary path fails or when the backup

path is programmed to duplicate messages. There is no option to backup path 8.

3.5

COMM TYPE: DD

Communication Type

Species the communication method the panel uses on this path to report system events

to DMP SCS-1R Receivers or non-DMP receivers. Default is DD for Path 1, and NONE for

Path 2-8.

NONE DD NET CID

NONE - For local systems. Selecting NONE ends communication programming.

DD - Digital Dialer communications to a DMP SCS-1R Receiver.

NET - Network communication using the panel onboard network connection. The DMP

Network/Output reporting format is transmitted over a data network to the SCS-1R

Receiver.

CID - This option allows the panel to communicate to non-DMP receivers using the

Contact ID format.

CELL - This option allows communication over the cellular network using the 463G, 463C,

464-263C, 464-263H or CellComRT Cellular Communicators.

232 - This option sends serial data and can be used for radio backup or other

communication options, and uses the on-board serial port.

Select 232 when using a 462N Interface Card or DB-9 backup communications by directly

connecting to the RS-232 port on the panel. If using the on-board RS-232 port, set the

XR500 Series panel J23 jumper to R and briey reset the panel using the J16 jumper to

activate RS-232 operation. Refer to the XR500 Series Installation Guide (LT-0681).

3.6

PATH TYPE: BACKUP

Path Type

The Path Type denes if the path is Primary or Backup. Because Path 1 is Primary, this

option only displays for paths 2-8. Default is Backup.

Note: If the Primary Communication Type is CELL, then the backup Communication Type

can only be NET or 232.

PATH: -

CELL 232

PRIMARY BACKUP

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 83 84

Kommentare zu diesen Handbüchern

Keine Kommentare

Digital Monitoring Products Canadain XR500 Bedienerhandbuch Seite 17

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Digital Monitoring Products Canadain XR500