Digital Monitoring Products 1912XR Installationsanleitung PDF herunterladen (Seite 28)

Digital Monitoring Products, Inc.

1912XR Programming

Page 22

12.1 AREA INFORMATION - Allows you to assign functions to the different areas

within a partition. All non-24 hour loops must be assigned to an active area. See

Loop Information in section 13.1.

You activate an area by assigning it a name. See section 12.13. A name is given

to each active area in place of a number to assist the user during arming and

disarming.

12.2 PARTITION NUMBER - Enter the partition number to program. Partition 1 using

area arming can have up to eight areas on the 1912XR panel. Partitions 2, 3, and

4 using area arming can each have up to four independent areas.

This prompt is not displayed if you only entered one partition in Device Setup.

12.3 MODE - This option allows you to program how the areas in this partition

operate. The options you can choose are:

AREA ARMING - in which all areas of the partition can be programmed and

operated independently. Partition 1 provides up to eight areas and partitions 2 to

4 each provide up to four areas.

ALL/PERIMETER - in which only areas one and two are activated and operate as

a perimeter and interior system only.

HOME/AWAY - in which three areas can be used: Perimeter, Interior, and

Bedrooms. If you assign loops to the Bedrooms area, the keypad display shows

HOME SLEEP AWAY when the user goes to arm the system. If you do not

assign loops to the Bedrooms area, the keypad only displays HOME AWAY to

the end user.

With the HOME SLEEP AWAY option, the user can:

1. Select HOME to arm just the perimeter.

2. Select SLEEP to arm the perimeter and interior (non bedroom areas).

3. Select AWAY to arm all three areas.

12.4 EXIT DELAY - Enter the exit delay time for all exit type loops in this partition.

When the exit delay time starts, all activity on that loop and other non-24 hour

loop types in the area are ignored until the exit delay expires. This delay

countdown is displayed on the keypad. If an exit type loop is placed in a bad

condition at the end of the exit delay, the system sounds the alarm bell for 15

seconds and sends an exit error report to the alarm receiver. The output cannot

be turned on from the Outputs On/Off option of the User Menu.

If any other loop type is placed in a bad condition at the end of the exit delay an

alarm is indicated. The exit delay can be from 1 to 250 seconds. Enter zero to

disable the Exit Delay feature.

12.5 BURGLARY OUTPUT - This output is turned

any time a burglary type loop in

this partition is placed in alarm. The output is turned

off

by a Cutoff Time (see

section 8.5B) or when you disarm the area in which the alarm occurred and no

other burglary type loops are in alarm. Outputs can also be turned off by a user

through the Alarm Silence and Outputs On Off User Menu options.

12.6 OPENING/CLOSING REPORTS - This option allows an Opening report to be

sent to the SCS-1 Receiver whenever an area within this partition is disarmed.

A Closing report is also sent to the SCS-1 Receiver when any area within this

partition is armed.

PARTITION NO: 1

MODE: AREA SYS

AREA A / P H / A

AREA INFORMATION

EXIT DELAY: 45

OPN/CLOS YES

BURGLARY OUT: 0

12-AREA INFORMATION

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 41 42

Kommentare zu diesen Handbüchern

Keine Kommentare

Digital Monitoring Products 1912XR Installationsanleitung Seite 28

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Digital Monitoring Products 1912XR