Digital Monitoring Products 1912XR Installationsanleitung PDF herunterladen (Seite 14)

Digital Monitoring Products, Inc.

1912XR Programming

Page 8

3.2B EXISTING PRINTER - One or more options in Printer Reports has been enabled.

See section 11.1. You must remove any Printer Reports programming before

using the DNET option to interface with a data network.

3.3 2ND PHONE LINE - Allows you to use a second phone line to send reports to the

SCS-1 Receiver should the first phone line fail. If 2ND LINE is YES, you'll need

to install a DMP 893 Dual Line Module to connect both the main and secondary

phone lines. The 893 provides supervision of both phone lines.

Both DD and MPX type systems can be backed up with a dialer or cellular line.

Multiplex lines cannot be used as a secondary line.

NONE - A second line is not used.

DD - Dialer communication to a DMP SCS-1 Receiver.

CELL - Cellular communication with Cell-Miser™ restrictions. When Cell-Miser is

selected, the following call restrictions apply to the panel.

1. Only loop alarms, Ambush, Line 1 Trouble, Abort, Recall Test, and Delayed

Events can be sent over the cellular system. Delayed Events are only sent

if the cellular call was made for one of the other allowed reports.

2. Line 1 Trouble in sent only once during each armed period.

Area code selection for cellular communication:

Version 1912XR/112 firmware allows you to

enter a letter "C" in the first or second phone number in the panel's Communication section of the

Programmer. When entered, the characters before the "C" are only used when a 2nd LINE Cellular

call is being made. All other calls made on the main line will only use the characters entered after

the letter "C". The letter "C" is never dialed and is recognized by the panel as a marker only.

HST (HOST) - DTE asynchronous communication to a DMP SCS-1 Receiver or

Host automation system. If HST is selected as the Communication Type in

section 3.2, HST will not be displayed as an option in 2ND LINE. If HST is

selected for 2ND LINE, all loop alarms and restorals are duplicated on the

asynchronous channel in addition to the main communication method.

When HST is used as the main or 2ND LINE communication method, the

account number must not begin with a number that matches a line number being

used for multiplex service on the same SCS-1 Receiver. This allows the

Redisplay Non-Restored status list to work properly in receivers with SCS1/805

firmware.

3.3A TEST FREQUENCY - Specifies the communication test interval for the second

phone line. This is displayed if 2ND LINE is programmed as DD or CELL.

NONE - No communication test is made on the second line.

REG - A 2ND LINE communication test is made each time the regular

communication test is completed.

7 - A communication test is made every 7 days at the test time programmed for

the regular communication test. Test time deferrals are disregarded.

30 - A communication test is made every 30 days at the test time programmed

for the regular communication test. Test time deferrals are disregarded.

If the 2ND LINE test fails to communicate after 10 attempts, the regular communication channel

sends a WARNING: PANEL BACKUP COMMUNICATION FAIL (S12) report. The next time the

panel sends a report over the 2ND LINE, the regular communication channel sends a BACKUP

COMMUNICATION LINE RESTORED (S04) report.

3-COMMUNICATION

NONE DD CELL HST

2ND LINE: NONE

NONE REG 7 30

TEST FREQ: NONE

EXISTING PRINTER

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 41 42

Kommentare zu diesen Handbüchern

Keine Kommentare

Digital Monitoring Products 1912XR Installationsanleitung Seite 14

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Digital Monitoring Products 1912XR