Digital Monitoring Products XT50 Installationsanleitung PDF herunterladen (Seite 14)

XT Series Programming Guide Digital Monitoring Products

COMMUNICATION

Communication

3.1 Communication

The Communication section allows you to congure the communication settings for the

XT30/XT50 panel. After choosing the Communication Type, continue through the list of

options.

3.2 Account Number

Enter the account num ber sent to the receiver.

DD, NET, CELL - The range of account numbers for Digital Dialer, Network, and Cell is 1

to 65535. For account numbers of four digits or less, you do not have to enter leading

zeros. The panel automatically right justies the account number.

CID - The account number range for this format is 1 - 9999.

3.3 Transmission Delay

Enter the number of seconds (15 to 45 seconds) the panel waits before sending burglary

alarm reports to the receiver. The bell and relay outputs are not delayed during this

period. Program Burglary Outputs for steady, and set Abort Reports to YES if Opening and

Closing reports are not being sent. Enter 0 (zero) to disable this function. The default is

30.

If the area where the alarm occurred is disarmed during the Transmit Delay time, only

an Abort Report (S45) message is sent to the receiver. If the area where the alarm

occurred is disarmed after the alarm message is sent to the receiver but before the Bell

Cutoff time expires, even if the alarm was silenced, an Alarm Cancelled (S49) message is

sent. The Alarm Cancelled report cannot be disabled.

3.4 Communication Type

This species the communication method the panel uses to contact the receiver. Press

any Select key to display the following communication options:

DD - Digital Dialer communication to DMP SCS-1R or SCS-VR Receivers.

CID - Contact ID dialer communication to non-DMP receivers. This format sends the

report codes of the Ademco Contact ID communication format.

NET - Network communication to DMP Model SCS-1R Receivers.

CELL - Cellular communication to DMP Model SCS-1R or SCS-VR Receivers.

NONE - For local systems. Selecting this ends communication programming.

NOTE: The Backup Dialer, Backup Cellular, Check-in Minutes, and Failed Minutes options

revert to their default values when the communication type is changed. All other

communication programming items remain at their programmed values.

3.5 Backup Dialer

Backup Dialer option is available if COMM TYPE is set for NET. The Backup Dialer tries

to send the message after the main communication fails for 60 seconds on NET. If the

backup dialer fails then the message is discarded.

3.6 Backup Cellular

Backup Cellular option is available if COMM TYPE is set for NET or DD/CID. The Backup

Cellular tries to send the message after the main communication fails for 60 seconds

on NET and 10 dial attempts with DD/CID. If the backup dialer fails then the message is

discarded.

3.7 Test Time

Press COMMAND to enter the Test Time. Enter the time of day the panel sends the test

report to the SCS-1R Receiver. Use entries between 12:00 to 11:59 and then choose AM

or PM.

3.8 Test Days

Enter how often the panel test report is sent to the receiver for each communication

type programmed. Enter from 1 to 60 days. Enter zero to disable the test report. Default

is 1 (one) day. These options only display if a test time is entered and that particular

communication method is being used.

COMMUNICATION

ACCOUNT NO:

XMIT DELAY: 30

COMM TYPE: DD

DD CID NET CELL

NONE

BACKUP DIALER

NO YES

BACKUP CELL

NO YES

TEST TIME

00:00 AM PM

NET TEST DAYS: 1

DIAL TST DAYS: 1

CELL TST DAYS: 1

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 54 55

Kommentare zu diesen Handbüchern

Keine Kommentare

Digital Monitoring Products XT50 Installationsanleitung Seite 14

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Digital Monitoring Products XT50