Digital Monitoring Products XR20 Installationsanleitung PDF herunterladen (Seite 24)

Digital Monitoring Products XRSuper6/XR20/XR40 Installation Guide

ComplIanCe

ANSI/UL 609 Specications

Local Burglar Alarm Units and Systems

21.1 Entry Delay

The maximum entry delay must not exceed 60 seconds with the Model 350A housing. See LT-0305.

21.2 Bell

A local audible signal appliance must be used.

In a mercantile burglar alarm system, a mercantile alarm sounding device located within a building but

outside the protected area, is acceptable, provided it is rated for outside service and alarm conditions are

transmitted to:

a) The dispatch location of the law enforcement agency having jurisdiction over the protected property or

b) A central station or residential monitoring station complying with the Standard for Central Station Alarm

Services, UL 827.

In a mercantile burglar alarm system, an alarm sounding device located within the area of greatest

protection, or outside the area of greatest protection but within an area protected by an alarm system and

that shares a common control unit with the system installed in the area of greatest protection, is acceptable

provided it is rated for inside service and alarm conditions are transmitted to:

a) The dispatch location of the law enforcement agency having jurisdiction over the protected property or

b) A central station or residential monitoring station complying with the Standard for Central Station Alarm

Services, UL 827.

An inside sounding device shall be mounted at least 10 feet (3.05 m) above the oor or at the surface of the

ceiling. When there is xed construction within the area that could provide access for an intruder, the alarm

sounding device shall also be mounted at least 4 feet (1.2 m), as measured horizontally, away from the

edges of the xed construction or at least 10 feet (3.05 m) above it so as to minimize access by an intruder.

21.3 Bell Cutoff

The bell cutoff time cannot be less than 15 minutes. See the Programming Guide (LT-0305).

21.4 Automatic Bell Test

The Automatic Bell Test option must be programmed as YES. See the Programming Guide (LT-0305).

21.5 Mercantile Safe and Vault

When the DMP Model 350A housing is used, the panel provides operation as a mercantile safe and vault

alarm. Bell Supervision and wiring must be in accordance with UL 681. If the panel is mounted outside the

safe or vault, tamper protection and the Sentrol Model 5402 or Potter EVD listed vibration detectors should

be used. The XRSuper6/XR20/XR40 does not provide operation as a Bank Safe and vault alarm.

21.6 Wireless Arming Mode

The System Options Mode for arming must be programmed as Area or All/Perimeter (A/P). See the

XRSuper6/XR20/XR40 Programming Guide (LT-0305).

21.7 Wireless Tamper

The Zone Information Disarmed Open Message to Transmit must be programmed Trouble (T). See the

XRSuper6/XR20/XR40 Programming Guide (LT-0305).

21.8 Wireless External Contact

When used, the External Contact of 1101, 1102, or 1103 must be programmed Normally Closed. See the

XRSuper6/XR20/XR40 Programming Guide (LT-0305).

21.9 Wireless Supervision Time

The Zone Information Supervision Time cannot be set to 0 (zero). See the XRSuper6, XR20, XR40

Programming Guide (LT-0305).

21.10 Wireless Audible Annunciation

The Wireless Audible option must be selected as ANY for commercial applications.

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 30 31

Kommentare zu diesen Handbüchern

Keine Kommentare

Digital Monitoring Products XR20 Installationsanleitung Seite 24

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Digital Monitoring Products XR20